-
VersionDetect Not working with two ports. ETCNet2 Two Port DMX Nodes prior to v4.0.0 will not understand an Update command from VersionDetect as indicated by the icon. To update these nodes with the version of software the nodes are currently in. This is because two ports prior to version 4 need RCC...
-
Two Port Wallmount Node Two Port Touring Node The ETCNet2 Two Port Node was available as either a wallmount (backbox mounting) version or as a touring version with either two male or two female 5 pin XLR connectors. Similarly to other Net2 products the connectors can be inputs or outputs irrespective...
-
Network Configuration Editor (NCE) ETC's Network Configuration Editor (NCE) is a spreadsheet-style software program designed to make configuring ETCNet2 TM DMX and Video nodes easy. With NCE, you can configure the paramaters of any port on any ETCNet2 node in a NET2 system. Through an Ethernet connection...
-
Problem: My RFU will not work with my Net2 Video Node. Answer: Make certain that you're video node is running 2.0 code.
-
The ETCNet2 DMX Node provides a way to either input or output DMX from a Net2 Network system. The node can also be used in a Net1 system similar to an RIU. There were several variants produced : Connectors could be either front or rear mounted DMX connectors were available as 4 male, 4 female or a mixture...
-
Question: In which direction do you move the termination switch on the ETCLink/RFU PCB to terminate? Answer: Towards the J5 connector is terminated
-
Default IP configuration by product Product IP Address Subnet Mask Gateway IP Unison 10.101.10.101 255.255.0.0 10.101.10.101 Obsession Primary RPU 10.101.30.101 255.255.0.0 10.101.30.101 DMX Node 10.101.0.99 255.255.0.0 0.101.0.99 Default subnet mask and gateway Item Value Subnet Mask 255.255.0.0 Default...
Posted to
ETC Product Wiki
by
Tracy.Fitch
on
05-12-2010
Filed under: CEM+, Congo, CongoJr, DMX, Element, Emphasis, Eos, GCE, Ion, KnowledgeBase, Legacy Unison, Net2, Net3, Obsession, ObsessionII, Sensor+, Unison, WRFU
-
1-PORT GATEWAY ISSUE There have been reports of issues with 1-Port Net3 Gateways running firmware version 4.0.0 (distributed with NCE 4.3.0) running in Net2 mode with Eos/Ion consoles running software versions 1.8.1, 1.8.2, and 1.9.0. After using the console for a period of time without changing any...
-
Attached are the instructions for configuring an ETC supplied Dell Ethernet Switch for a typical ETCNet2 and Net3 installation. Note that switches generally ship configured from ETC, these instructions are for reference in case a switch needs to be reset. 3771.4000M2202_revA.pdf
-
When equipment goes bad out in the field, it's often extremely helpful if the owner/end user can keep track of the circumstances of the failure. This is especially true when the problem is intermittent and might not occur when the technician is present. Service Technicians are exceptionally skillful...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
08-24-2009
Filed under: AAS, Acclaim, arri, ASTS, AVAB, CEM, CEM+, Congo, CongoJr, cRRFU, DAS, Dimmer, Distribution, DMX, ECMUX, Element, ELTS, Emphasis, Eos, ETCLink, Ethernet, Express, Expression, GCE, Idea, Ion, Irideon, K96, KnowledgeBase, Legacy Unison, LMI, Lon, MDD, MDR, MicroII, MicroVision, MIDI, MPE, NCE, Net2, Net3, Obsession, ObsessionII, Pharos, RDM, Response, RFR, RFU, RRFU, RS-232, RVI, Sensor, Sensor+, SineWave, SmartBar, SmartFade, SmartFadeML, SmartModule, SMPTE, Source Four, Source4, Touchscreen, Unison, Vision, WRFU